Smart IoT Sensor - HW - Revision history

Arl at 13:07, 19 January 2018

2018-01-19T13:07:38Z

Lcs: /* Battery */

2017-03-13T16:27:21Z

‎Battery

Lcs: /* Pictures */

2017-03-13T16:08:11Z

‎Pictures

Lcs: /* Pictures */

2017-03-13T15:47:17Z

‎Pictures

Arl: /* GPIO available */

2017-03-09T15:44:37Z

‎GPIO available

Lcs: Created page with "Category:Smart IoT Sensor == Features == == Pictures == 500px 500px == Electrical Specification == == Included M..."

2017-01-15T22:52:58Z

Created page with "Category:Smart IoT Sensor == Features == == Pictures == 500px 500px == Electrical Specification == == Included M..."

New page

[[Category:Smart IoT Sensor]]
== Features ==

== Pictures ==

[[File:SIoTS_PCB_top.jpg|500px]]

[[File:SIoTS_PCB_bot.jpg|500px]]

== Electrical Specification ==

== Included Modules and chipsets ==
=== LoRa/Sigfox MM002 ===

[http://www.nemeus.fr/en/nemeus-mm002-2/ NEMEUS: MM002 datasheet]

The Nemeus MM002 is wired using UART and a wakeup pin.

{| class="wikitable"
!colspan="5"|Pinning relations
|-
|Physical pin
|Port pin
|Function pin on sensor
|Function pin on Arduino
|Atmel label
|-
|28
|PA19
|TX
|RX (Serial2)
|SERCOM1/PAD[3]
|-
|27
|PA18
|RX
|TX (Serial2)
|SERCOM1/PAD[2]
|-
|9
|PA04
|WakeUp
|A3
|
|}

=== Bluetooth Smart nRF51822 ===
[http://infocenter.nordicsemi.com/pdf/nRF51822_PS_v3.1.pdf Nordic Semi: nRF51822 datasheet]

the nRF51822 is wired to an Arduino UART port. (Variant AC : 256KB Flash / 32KB Ram)

{| class="wikitable"
!colspan="7"|Pinning relations
|-
|Physical pin (SAMD)
|Physical pin (nRF51)
|Port pin (SAMD)
|Port pin (nRF51)
|Function pin on sensor
|Function pin on Arduino
|Atmel label
|-
|31
|17
|PB23
|P0.11
|TX
|RX (Serial)
|SERCOM5/PAD[3]
|-
|30
|15
|PB22
|P0.09
|RX
|TX (Serial)
|SERCOM5/PAD[2]
|}

=== GPS/GNSS SIM33ELA ===
[https://www.silabs.com/Support%20Documents/RegisteredDocs/BGM111_datasheet.pdf SIMCom: SIM33ELA datasheet]

The SIM33 GPS is wired using UART to the Arduino.

{| class="wikitable"
!colspan="5"|Pinning relations
|-
|Physical pin
|Port pin
|Function pin on sensor
|Function pin on Arduino
|Atmel label
|-
|15
|PA10
|RX
|TX (Serial1)
|SERCOM0/PAD[2]
|-
|16
|PA11
|TX
|RX (Serial1)
|SERCOM0/PAD[3]
|-
|3
|PA02
|Power enable
|A0
|
|-
|29
|PA20
|Fix GPS
|6
|
|}

== Included Sensors ==
===ADXL345===
The ADXL345 accelerometer is wired to the I2C bus, and can use two interrupts to manage acceleration events (tap, activity...).

{| class="wikitable"
!colspan="4"|Pinning relations
|-
|Physical pin
|Port pin
|Function pin on sensor
|Function pin on Arduino
|-
|31
|PA22
|SDA
|SDA
|-
|32
|PA23
|SCL
|SCL
|-
|7
|PB08
|Interrupt 1
|A1
|-
|8
|PB09
|Interrupt 2
|A2
|}

===BMP280===

The BMP280 temperature and pressure sensor is wired on I2C bus.

{| class="wikitable"
!colspan="4"|Pinning relations
|-
|Physical pin
|Port pin
|Function pin on sensor
|Function pin on Arduino
|-
|31
|PA22
|SDA
|SDA
|-
|32
|PA23
|SCL
|SCL
|}

== GPIO available ==

You can use these additional pins :
{| class="wikitable"
!colspan="3"|Pinning relations
|-
|Physical pin
|Port pin
|Function pin on Arduino
|-
|x
|GND
|x
|-
|47
|PB02
|A5
|-
|10
|PA05
|A4
|-
|9
|PA04
|A3
|-
|x
|3V3
|x
|-
|21
|PA12
|MISO
|-
|20
|PB11
|SCK
|-
|19
|PB10
|MOSI
|-
|4
|PA03
|AREF
|-
|31
|PA22
|SDA (shared with sensors)
|-
|32
|PA23
|SCL (shared with sensors)
|-
|26
|PA17
|13
|-
|30
|PA21
|7
|-
|11
|PA06
|8
|-
|12
|PA07
|9
|}

== Buttons and LEDs ==

=== Reset Button ===
A reset button est available on board: pushing the reset button will only reset the SAMD21.
In others words, the Arduino bootloader will restart and jump to the user's application.

If the reset is pushed twice, the MCU will remain in bootloader mode, allowing USB emulation and serial communication.

=== User Button ===
The user button is connected in pull down to the MCU.

{| class="wikitable"
!colspan="4"|Pinning relations
|-
|Physical pin
|Port pin
|Function pin on sensor
|Function pin on Arduino
|-
|25
|PA16
|USER button
|11
|}

=== LED ===

The RGB leds are wired on simple GPIOS.

{| class="wikitable"
!colspan="4"|Pinning relations
|-
|Physical pin
|Port pin
|Function pin on sensor
|Function pin on Arduino
|-
|23
|PA14
|BLUE
|2
|-
|14
|PA09
|GREEN
|3
|-
|24
|PA15
|RED
|5
|}

== Battery ==

An optional battery can be added inside the case. A 2 pins connector is available on board, leading to a power and charging management IC for the entire board.
The Smart IoT Sensor can work by itself without any external connection.

If an USB connection is made, the USB's power will be drained to the battery by the charging IC.
While the board is connected, it will use the USB power supply first.

== Case ==

The Smart IoT Sensor features a 50*50*25mm case.
All the hardware is all-included inside the case. There is no visible outside antenna.

The case has one miniUSB connector for USB communication on one side, and works as power supply as well.

The user LED is visible on the top of the case.

== Antennas ==

=== Bluetooth Smart antenna ===

The board embeds an RF Ceramic Antenna.

=== GPS/GNSS (SIM33ELA) antenna ===

The antenna is integrated on the module.

=== LoRa/Sigfox (MM002) antenna ===

We provide a finely tuned PCB antenna onboard.

There is also an UFL connector in case you need an external antenna.

== SWD Debug Port ==

The SWD 9 pins connector onboard can be used with your SWD debugger.

We suggest you to use a [https://www.segger.com/jlink-adapters.html#CM_9pin J-Link 9-pin Cortex-M Adapter] with the [https://www.segger.com/jlink_base.html J-Link BASE SWD debug probe]

The SWD switch allows you to choose the SAMD21 or the BLE as SWD target for the debug probe.

===SWD connection to the SAMD21===

You received your board with a preloaded firmware in the SAMD chipset.
If you bricked your board, this procedure can be used to re-flash the arduino firmware.

Set the SWD switch to MCU position.
launch JLinkGDBServer:
/opt/SEGGER/JLink/JLinkGDBServer -if SWD -device ATSAMD21G18 -speed 4000

You should see "Listening on TCP/IP port 2331"

From gdb, connect to the gdbserver:
arm-none-eabi-gdb
(gdb) target remote localhost:2331
(gdb) restore bootloader.hex

===SWD connection to the nRF51822===

You received your board with a preloaded firmware in the BLE chipset.
This firmware is a basic UART to BLE demonstration software.

We describe this procedure in case you need to re-flash the bluetooth firmware to match your specific needs.

Set the SWD switch to BLE position.

The full support can be found from [Nordic https://devzone.nordicsemi.com/tutorials/7/]
Here is an abstract for the UART BLE example:

Install GNU Make
sudo apt-get install build-essential checkinstall

Download [http://developer.nordicsemi.com/ Nrf51 SDK 11.0.0].

Download [http://developer.nordicsemi.com/ nRF5x Command Line Tools].

Set the toolchain path in makefile.windows or makefile.posix depending on platform you are using:
<SDK>/components/toolchain/gcc/Makefile.[platform]

You have to choose the correct LD script for the nRF81822. Please use pca10028 for 256kB of flash and 32KB of ram.
Update this file:
<SDK>/examples/bsp/pca10028.h
#define RX_PIN_NUMBER 9
#define TX_PIN_NUMBER 11
#define HWFC false

We need to update the main file in uart_init() function :
<SDK>/examples/ble_peripheral/ble_app_uart/main.c
APP_UART_FLOW_CONTROL_DISABLED
UART_BAUDRATE_BAUDRATE_Baud9600

Now, we can build it, go to:
<SDK>/examples/ble_peripheral/ble_app_uart/pca10028/s130/armgcc

build and flash the BLE chip:
make
make flash_softdevice
make flash

== Certification ==

@@ Line 2: / Line 2: @@
 == Features ==
-[[File:SIS_PCB_front.jpg|500px]]
+{| class="wikitable"
+|-
-[[File:SIS_PCB_back.jpg|500px]]
+! Front !! Back
 == Electrical Specification ==

@@ Line 506: / Line 506: @@
   <SDK>/components/toolchain/gcc/Makefile.[platform]
-You have to choose the correct LD script for the nRF81822. Please use pca10028 for 256kB of flash and 32KB of ram.
+You have to choose the correct LD script for the nRF51822. Please use pca10028 for 256kB of flash and 32KB of ram.
 Update this file:
   <SDK>/examples/bsp/pca10028.h

@@ Line 424: / Line 424: @@
 == Battery ==
-An optional battery can be added inside the case. A 2 pins connector is available on board, leading to a power and charging management IC for the entire board.
+A LP552036 battery is included and fit in the case. It could be plug to the 2 pins battery connector available on board. Battery is managed thanks to the power and charging management IC.
-The Smart IoT Sensor can work by itself without any external connection.
+So, when USB is plugged, the USB will charge the battery and power the device.
-If an USB connection is made, the USB's power will be drained to the battery by the charging IC.
+The LED indicates current status:
-While the board is connected, it will use the USB power supply first.
+* No color: Device is not plus to a USB powered
 == Case ==

@@ Line 4: / Line 4: @@
 == Pictures ==
-[[File:SIoTS_PCB_top.jpg|500px]]
+[[File:SIS_PCB_front.jpg|500px]]
-[[File:SIoTS_PCB_bot.jpg|500px]]
+[[File:SIS_PCB_back.jpg|500px]]
 == Electrical Specification ==

@@ Line 245: / Line 245: @@
 |9
 |}
 == Buttons and LEDs ==