Application Note: NIS Devices configuration - Revision history

Lcs: /* Usage */

2019-01-14T09:07:24Z

‎Usage

Lcs at 17:36, 11 January 2019

2019-01-11T17:36:42Z

Lcs at 15:07, 7 May 2018

2018-05-07T15:07:08Z

Lcs: Created page with "Category:Sensors Category:Application Notes = Configuration with Nemeus USB stick = Most of Nemeus devices can be reconfigured thanks to Nemeus USB stick and MM00..."

2018-05-07T14:13:06Z

Created page with "Category:Sensors Category:Application Notes = Configuration with Nemeus USB stick = Most of Nemeus devices can be reconfigured thanks to Nemeus USB stick and MM00..."

New page

[[Category:Sensors]]
[[Category:Application Notes]]

= Configuration with Nemeus USB stick =

Most of Nemeus devices can be reconfigured thanks to Nemeus USB stick and [[MM002_Configuration_Tool_Java|MM002 Java application]].

In addition of the Java application and the USB stick, it needs Yaml

= Usage =

Open "LoRa device config" in config Menu. The following display will show up :

[[File:NIS_device_configuration_0.png|Device configuration windows]]

The "devUid" field must be filled up with the device Uid of the device to be configured
The "Authentication Key" field must be filled up with the App_skey of the device to be configured

@@ Line 13: / Line 13: @@
 = Usage =
 Open "LoRa device config" in config Menu. The following display will show up :
@@ Line 22: / Line 33: @@
 The "Authentication Key" field must be filled up with the App<span style="color:#00FF00">S</span>Key of the device to be configured.
 == Reading device ==
+<br>
 When ready, user should set the device in "Test mode" as explained in the wiki (e.g. [[NIS-TR_Temperature_Sensor_(RTD)#Test_mode|Test mode for NIS-TR]] ). Then if you press "Read Device" button the following window should pop up.

← Older revision		Revision as of 17:36, 11 January 2019
Line 33:		Line 33:
	- device to be read is set in "Test mode" (Led of the device should blink regularly)		- device to be read is set in "Test mode" (Led of the device should blink regularly)
	- correct devUid and App<span style="color:#00FF00">S</span>Key has been entered. Please note that the key is the App<span style="color:#00FF00">S</span>Key and not the AppKey		- correct devUid and App<span style="color:#00FF00">S</span>Key has been entered. Please note that the key is the App<span style="color:#00FF00">S</span>Key and not the AppKey
		+
		+	== Writing device ==
		+
		+	Just push to the Write Dev button.
		+	<br>
		+	If the device has been disconnected from Test Mode you just need to put it again in Test mode and write the device (you don't need to read it again).
		+
		+	== Applying new configuration ==
		+
		+	Depending on the parameters, the configuration could be used directly or you might need to restart the device,
		+	To do so
		+	-a) remove, insert battery
		+	-b) Set the magnet around 20 seconds (until it stop blinking and then remove it immediatly)
		+
		+	After restart you may need to set the device back to IDLE mode, A join will be performed by LoRaWan device.

@@ Line 6: / Line 6: @@
 Most of Nemeus devices can be reconfigured thanks to Nemeus USB stick and [[MM002_Configuration_Tool_Java|MM002 Java application]].
-In addition of the Java application and the USB stick, it needs Yaml
+In addition of the Java application and the USB stick, it needs Yaml File for the device configuration.
@@ Line 16: / Line 16: @@
 Open "LoRa device config" in config Menu. The following display will show up :
-[[File:NIS_device_configuration_0.png|Device configuration windows]]
+[[File:NIS_device_configuration_1.png|Device configuration windows]]
-The "devUid" field must be filled up with the device Uid of the device to be configured
+The "devUid" field must be filled up with the device Uid of the device to be configured.
-The "Authentication Key" field must be filled up with the App_skey of the device to be configured